Joseph Engineering Services
Book a discovery call
Federated BIM model, mixed-use development

Systematized BIM services in Syria.

Production, coordination and governance to ISO 19650, delivered as a full BIM team for consultants, contractors and developers. No internal hire, no management overhead.

Explore the pilot programme Get the ISO 19650 template pack
Design-side

For consultants

Design and documentation production at reconstruction volume, modelled to your BEP, so a lean practice can carry a large programme without staffing up against uncertain timelines.

Explore Build-side

For contractors

Trade coordination and shop drawing throughput absorbed offshore, with clashes resolved in the model before they reach a site where materials and access are already constrained.

Explore Owner-side

For developers

A single information standard enforced across every consultant and contractor on a scheme, so a rebuilt asset hands over with data that supports operation and future phases, not just a set of drawings.

Explore

Early reconstruction needs modelling capacity before the market can rebuild it.

The engineers, coordinators and information managers a national rebuild will consume cannot be hired at the pace the programme demands, and much of that skill base has to be rebuilt alongside the country. JES brings a delivered team of 260+ engineers to the work, so a masterplan, a housing scheme or an infrastructure package runs on a proven system from day one instead of waiting on recruitment.

Prestige One
Al-Futtaim
AECOM
Dar Al-Handasah
Arup
WA International
SCDA
Dezigntechnic
H2R Design
Innovo
M4
MNG
Günal
ALEC
ALEMCO
Voltas
ALEC Fitout
DEPA
Al Tayer Stocks
Abaad Wood
Prestige One
Al-Futtaim
AECOM
Dar Al-Handasah
Arup
WA International
SCDA
Dezigntechnic
H2R Design
Innovo
M4
MNG
Günal
ALEC
ALEMCO
Voltas
ALEC Fitout
DEPA
Al Tayer Stocks
Abaad Wood

Six services. One delivery team.

Each service runs through the same Author-Checker-Approver gates and ERP tracking, against a single ISO 19650 baseline that holds from a housing block to a district masterplan.

BIM Delivery, fully coordinated multidiscipline model

BIM Delivery.

Coordinated multidiscipline models and drawing sets produced to your BEP, checked before they reach your reviewers, so early reconstruction work starts on a clean information base.

Explore service
VDC, 4D sequencing and coordinated site logistics model

Virtual Design & Construction.

4D and 5D analysis that puts programme and cost questions in front of the team while the sequence and the budget can still be changed cheaply.

Explore service
CDE workspace

Information Management

Your CDE, naming protocol and exchange workflows administered day to day, so your information manager governs the project instead of policing uploads.

Explore
Digital Twins, asset information model of heritage and tower development

Digital Twins

Operational asset models with structured data at handover, built for the operators who will run and maintain rebuilt assets over the long term.

Explore
QTO · procurement BOQ

QTO & Cost

Model-based quantities tied to your cost plan, so funders, contractors and the design team all measure from one defensible number.

Explore
LiDAR, point cloud scan of industrial facility

As-Built Documentation

Laser-scan verification and record modelling that document what was actually built and what remains of existing structures, not what was once drawn.

Explore

Every capability, none of the overhead

The whole BIM scope from one team, so adding a service never means onboarding another supplier mid-programme.

  • 3D BIM modelling

    Full-discipline Revit production with Navisworks federation, run to a single modelling standard your reviewers learn once.

  • Revit family creation

    Office-standard Revit families authored to your graphics, parameters and LOD specification, from joinery to plant.

  • 4D, 5D and 6D simulation

    Sequencing, cost and performance data linked to the model, giving planners and commercial teams one model to work from.

  • Shop drawings & detailing

    Shop drawings detailed to fabrication tolerance and checked against the federation before they leave JES.

  • Scan to BIM

    Point clouds processed into as-built models, so existing and partially standing structures enter the programme as accurate, working models.

  • CAD to BIM conversion

    Flat 2D archives converted into coordinated 3D models, so legacy records and older assets get the same single source of truth as new work.

  • BIM for facility management

    Handover data structured for CAFM import, so a rebuilt asset has a working operating model before it is occupied.

  • Quantity take-off & BOQ

    Take-off straight from the coordinated model, mapped to your measurement rules and cost codes.

Three sets of eyes before it leaves.

Every JES deliverable moves through a fixed Author-Checker-Approver gate, tracked in the CDE. The same standard whether it's engineer 3 or engineer 250.

Author
Model and documentation produced to the MIDP task card. Self-review against the project QA checklist before submission.
Status: WIP
Checker
Independent review against the BEP and federated model. Defects logged, deviation report returned to Author.
Output: Deviation report
Approver
Signed off against EIR and LOIN. Promoted from WIP to Shared or Published in the CDE.
Status: Published

Without that discipline the costs land where a reconstruction budget can least absorb them: a recurring modelling error multiplying across a programme, rework consuming scarce funding, and information gaps surfacing when a scheme is audited or handed to an operator. JES files clear three review stages before they reach your CDE, and the record of who authored, checked and approved each one travels with the file.

The record so far, on Gulf programmes

Towers, transit packages and resort programmes delivered in the Gulf on tight schedules, run on the same ISO 19650 system a reconstruction programme needs. A sample below.

View all

What changes when delivery runs to a system

  • Construction-ready output

    Coordinated, clash-checked packages issued against your programme dates, so scarce review and site time goes to the build, not to correcting the model.

  • Your team stops chasing deliverables

    Deliverable status lives on an ERP dashboard, not in a chain of chasing emails between your office and ours.

  • Runs to standard

    ISO 19650 wired in from kick-off, with EIR, BEP and CDE structure agreed before modelling starts.

View all
From LOD 350 to fabrication-ready6 min
Coordination

From LOD 350 to fabrication-ready

Why "coordinated" models still cause site rework, and the handoff that fixes it.

Read
The BEP subcontractors actually follow5 min
Delivery

The BEP subcontractors actually follow

The difference between a filed document and a working agreement is five sections.

Read
Clash detection to zero5 min
Coordination

Clash detection to zero

Zero hard-clash is table stakes. Here is the tolerance standard we hold a federated model to before sign-off.

Read
QTO as the single source of truth for variations6 min
Cost

QTO as the single source of truth for variations

When quantities come straight from the model, variations stop being arguments and become deltas.

Read
As-built from day one5 min
Handover

As-built from day one

Retrofitting an as-built at practical completion is a tax. Updating it weekly is a habit.

Read

Common questions about BIM in Syria

Both. We produce the models, drawings and coordination, and we govern them through the BEP, the CDE and the Author-Checker-Approver gate. One accountable team carries the work, not a consultancy that advises beside a shop that draws. For early reconstruction, that means production and standards start on a clean information base from the same delivery lead.

Yes. A delivery lead owns your programme, backed by 260+ engineers on one system, so a masterplan, housing or infrastructure package runs from day one rather than waiting on hiring. The engineers a national rebuild will consume cannot be recruited at the pace the work demands. We bring the team to the work and scale it against the programme.

Yes. Our BIM consultants embed in your delivery, set the BEP and LOD and hold the work to ISO 19650, with one named lead accountable across the programme. A masterplan or housing scheme joins a proven system while the local skill base is rebuilt alongside the country. Your reviewers govern the project rather than carry the modelling load.

Yes. We run laser scan to point cloud to a coordinated record model that documents what actually stands, including partially standing structures. That verified base is what every discipline coordinates against as existing fabric enters the programme. It gives reconstruction work accurate geometry rather than drawings that no longer match the ground.

We model architectural, structural and MEP in Revit, federate in Navisworks and run regular clash cycles on one model. Every file is authored, checked and approved against the BEP before issue, at construction tolerance. On reconstruction and new-build work alike, conflicts are resolved in the model before they reach a site where materials and access are constrained.

Cost follows scope, disciplines, the LOD you need and programme length, so we scope each engagement to the actual work rather than a flat day rate. A national masterplan carries more than a single housing scheme. A zero-cost pilot on one package lets you see the output and the QA gate before a reconstruction budget commits to more.

Nearby locations
Help yourself

Get the ISO 19650 Template Pack

The full ACA framework PDF, the Responsibility Matrix template, and the EIR / BEP checklist we use on every project.

Free download
Talk to us

Book a 30 minute discovery call with our team

We'll walk you through a live ERP dashboard from an active project and you'll walk away with our ACA template, whether or not we work together.

Book a call
Got a project?

One free package, no commitments

We run the ACA framework on a single package. You get ERP visibility from day one. Zero-cost pilot, capped scope, clear exit.

Request a pilot